HDPE Pipe Welding Machine is the use of positive and negative poles in the instantaneous short-circuit generated when the high-temperature arc to melt the solder on the welding and welding materials, to achieve the purpose of their combination. The structure is very simple, is a high-power transformers, HDPE Pipe Welding Machine generally according to the type of output power can be divided into two kinds, one is AC power; one is DC. The use of the principle of inductance made, the amount of inductance in the connected and disconnected will have a huge voltage changes, the use of positive and negative poles in the instantaneous short-circuit generated when the high-voltage arc to melt the solder on the electrode, to achieve their combination The purpose of HDPE Pipe Welding Machine can not be used in the process of maintenance and maintenance.
HDPE Pipe Welding Machine
1, check the welding machine output wiring specifications, solid, and outlet direction down close to the vertical, and the horizontal angle must be greater than 70 °.
2, check the cable connection of the screw fastening, screw specifications for the hexagonal bolts M10 × 30, flat pad, spring pad complete, no rust oxidation and other undesirable phenomena.
Precautions
1, the new or long unused HDPE Pipe Welding Machine, often due to moisture to make the winding, winding and chassis insulation resistance between the significant reduction in the beginning of the use of prone to short circuit and ground, resulting in equipment and personal accidents. Therefore, before using the table to check its insulation resistance is qualified.
2, start the new HDPE Pipe Welding Machine before, should check the electrical system contactor part is good, that is normal, can be started under no load test run. To prove that there is no electrical risk, before the test in the case of load test, and finally put into normal operation.
3, DC HDPE Pipe Welding Machine should be rotated in the specified direction, with a fan to pay attention to the direction of rotation of the fan is correct, should be used from the top of the blown. To achieve the purpose of cooling HDPE Pipe Welding Machine.
Different spot welding machine in the specific use to consider how to better use HDPE Pipe Welding Machine, make it the best effect, the following welding machine on the use of HDPE Pipe Welding Machine welding, to consider the matter.
1, the production of welding fixture: In order to facilitate welding, improve the quality and speed of welding, should be prepared in advance for a variety of welding equipment required for welding fixture.
2, select the HDPE Pipe Welding Machine with the spot welding head: the welding requirements of the solder joints are not the same, as well as welding metal wire material, the size of the shape is not the same, the need to initially select the appropriate spot welding head.
3, groping HDPE Pipe Welding Machine. Different welding metal due to the shape, thermal conductivity, melting point, between the two metals (welding lines and pads) with different performance, resulting in welding the required welding voltage, welding time and welding pressure is not the same, so need to explore the specific Welding voltage, welding time and welding pressure. In the exploration of the above parameters, the principle of adjustment from low to high. The final set of parameters should ensure that the welding process has good solder joint consistency and wide process tolerance.
4. familiar with the HDPE Pipe Welding Machine operation: including familiar with the placement of products when welding, familiar with the pedal trigger mode, familiar with the welding when the tweezers used, familiar with the microscope or monitor the next bit and other operations. The general staff about 8 hours can be skilled operation, to achieve the best capacity roughly takes a week.
5, the design is more suitable for the specific welding of the spot welding head and fixture
HDPE Pipe Welding Machine application: Widely used in a variety of small coil with the production of electronic components, such as high-frequency communications components, patch transformers, chip inductors, micro-speakers, induction IC card and other lead-line contact welding. The same can be welded all kinds of fine metal wire, metal belt, such as printed circuit board repair, solar cell welding and so on.
HDPE Pipe Welding Machine In use, the most important thing is to choose the appropriate welding head and fixture, which will be selected according to the specific use of location, or custom, it is indispensable to the electronics industry dedicated welding equipment.
Previous: The SLX-Centrifugal Spray Granulation Dryer Used In The Ceramic Industry
Next: The Core Principles And Operating Practices Of The SLT-High Speed Centrifugal Spray Dryer
Related News
- The working principle of hot blast stove
- Performance Of Centrifugal Spray Dryer Features
- Spray Drying Operation Requires
- General Principles Of Drying Equipment Selection
- Food Consumption Method For Drying Equipment
- Laboratory Spray Dryer Application
- Feed Water Pump
- Spray Granulation Drying Machine
- Dryer Instead Of Sun Drying
- Drying Equipment Widely Used In Areas
- The SLX-Centrifugal Spray Granulation Dryer Use...
- SLT-High Speed Centrifugal Spray Dryer Energy E...
- How Is The Welding Crack Of The HDPE Pipe Weldi...
- SLX-Centrifugal Spray Granulation Dryer Is One ...
- SLT-High Speed Centrifugal Spray Dryer Also Add...
- HDPE Pipe Welding Machine Before And After Use ...
- Spray Dryer Working Principle And Use Points
- Spray Dryer Rapid Development In The Field Of D...
Related Products

